No you do not have to get a new replacement transmission you can replace the output shaft or input shaft with a new one, also available is a transmission seal kit to replace any old transmission seals.
What is the correct oil I should be using in my transmission?admin2018-06-14T20:58:03+00:00
The transmission is filled with Penrite Synthetic 5 SAE 5W – 60 Oil. This oil can be substituted by Mobil 1, 5W – 50 (for Cold climates) or Mobil 1, 15W – 50 (for Hot climates) use only these oils unless instructed otherwise for correct servicing, draining & refilling procedures please read the instructions in the manual supplied. NOTE: Never allow contaminants to enter the transmission.
Where can I get the correct part number for the part I want to order?admin2018-06-14T20:59:34+00:00
The best place to get the correct and most up to date part numbers for your roller is on our web site www.truturf.com, go to manuals, this will also ensure that if there has been any superseded or updated parts than they will be listed and you will receive the latest part. If you are still having trouble email firstname.lastname@example.org or contact your local dealer.
Why is my drive roller spinning on takeoff?admin2018-06-14T21:00:02+00:00
Your drive roller is spinning on takeoff because of the motor is run at excessively high RPM, suggest 2/3 – ¾ of full throttle or you are depressing the foot pedal too quickly, (it’s like dropping the clutch pedal on a car and smoking up the tyres) depress the pedal gently in the direction that you want to go, get moving at least 24” (600mm) than depress the pedal to increase roller speed, be patient.
Why are my tyres wearing on my trailer arms?admin2018-06-14T21:00:42+00:00
This could be bearing wear from inside the smoothing or drive rollers, bearing wear in the housings that mounts the heads to the “T” frame or the “T” frame to the body, drive chain being to loose and not firm going around the sprockets or the drive belt on the ELTac machine not being tight and ratcheting/slipping on the sprockets.
Why is my ELTac or dc battery powered roller not rolling the full 18 greens?admin2018-06-14T21:05:01+00:00
This could be a battery issue, checking the batteries may require a high rate discharge check to determine if there is a faulty cell. Maintaining them is most important i.e. Water Levels, clean and tight terminals, tight nuts on battery leads, no loose wires, no damaged wires, battery charger is not working properly, ensure your machine is fully charged before leaving the workshop. Could be that the operator is overlapping excessively, rolling too far off the greens surface up and down the sides of the greens or not switching off the ignition when towing the roller between greens.
Why is my foot pedal sticking or hard to depress in any direction?admin2018-06-14T21:05:39+00:00
Could be that slides on the transmission yoke are sticky with dust, dirt, mud and grass which will stop the slides moving freely, this area has to be free, lubricated and clear of all the material to be able to slide freely.
Why is my Honda engine running rough?admin2018-06-14T21:06:17+00:00
It could be that the sprockets are incorrect, the old R9002 and R9003 (ISO) sprocket is a different pitch if trying to fit this to the R5137 or E7050 which is an (ANSI) pitch, the chain will not fit properly, it may be over tight or loose and will not fit correctly into the sprocket pitch and will cause rapid sprocket and chain wear.
Who deals with my warranty claim?admin2018-06-14T21:08:22+00:00
Through your local dealer. Tru-Turf Equipment has produced a simple machine that is extremely efficient, cost effective and easy to maintain. All engine, transmission and other components are available to you throughout a network of worldwide distributors and agents.
Our greens are heavily sloped, is that a problem?admin2018-06-14T21:09:24+00:00
Maximum traction in our machines is acquired via a high quality rubber-coated drive roller vulcanised to a steel tube, cylindrically machined for trueness and grip. This drive roller configuration, combined with a low centre of gravity, provides additional traction on sloping greeens. CAUTION: Always position the drive roller on the low side of the machine to ascend a slope; i.e. small rollers going forward.
Are the rollers heavy?admin2018-06-14T21:09:55+00:00
By design, Tru-Turf Rollers are both lighter in weight and ground pressure than other machines. Heavy machines compact the soil. We realise that the three main elements required to compact soil are – 1) water, 2) vibration and 3) weight. It’s a constant battle to eliminate soil compaction. We recommend incorporating lightweight rolling, deep spiking, drilling, coring and top dressing to assist in relieving this problem. Our technology has produced a greens roller with a lighter PSI (pounds per square inch) on the turf, than any other greens roller produced or a person walking across the green.
Are the rollers easy to transport?admin2018-06-14T21:10:25+00:00
At Tru-Turf, we have proudly produced a machine that almost completely eliminates the problems associated with other styles of rollers. We have a wider roll – 48″ with 2×24″(600mm) dual short surface rollers – which prevents line creasing on the green no matter which direction the green is rolled. The short surface rollers swivel and pivot in all directions, allowing the drive roller and smoothing rollers to be in contact with the turf surface at all times.